1 00:00:00,180 --> 00:00:05,490 Welcome to the first challenge video for this course in this video, you will be faced with three sketching 2 00:00:05,490 --> 00:00:07,500 challenges for each one. 3 00:00:07,620 --> 00:00:11,460 I will first describe the challenge and tell you the tools required to complete it. 4 00:00:12,390 --> 00:00:15,180 You will then be able to pause the video and try it out for yourself. 5 00:00:16,079 --> 00:00:19,080 I will then demonstrate how to go about each one of the challenges. 6 00:00:19,920 --> 00:00:21,570 Now let's get to the first one. 7 00:00:25,720 --> 00:00:29,980 In your first coaching challenge, you will be required to draw a tangle from scratch. 8 00:00:30,400 --> 00:00:34,660 You cannot use the rectangle tool, so this can be divided into four steps. 9 00:00:35,380 --> 00:00:40,240 You will first need to use the line tool to draw four connected lines similar to what has shown up here. 10 00:00:41,360 --> 00:00:44,510 Then you will need to add constraints to make it a perfect rectangle. 11 00:00:46,310 --> 00:00:51,770 In step three, you will need to add dimensions to make your rectangle 20mm by 30 millimeters. 12 00:00:52,550 --> 00:00:57,290 And finally, you will need to rotate your rectangle if required to make the length of the rectangle 13 00:00:57,290 --> 00:00:58,760 parallel with the x axis. 14 00:01:00,180 --> 00:01:02,970 Now, pause the video and try this yourself. 15 00:01:04,620 --> 00:01:06,510 Now that you've tried this, challenge yourself. 16 00:01:06,720 --> 00:01:11,220 Let me show you how to do it, so I have my four basic lines here. 17 00:01:12,300 --> 00:01:18,360 Firstly, I'm going to use the parallel constraint to make this in this line parallel. 18 00:01:18,720 --> 00:01:20,460 And then this and this one of. 19 00:01:22,230 --> 00:01:25,710 So I would first select this one and then this one. 20 00:01:26,220 --> 00:01:27,870 And they have now become parallel. 21 00:01:29,040 --> 00:01:31,200 Followed by this one and this one. 22 00:01:33,250 --> 00:01:38,230 And now I will use the preventively tool to make both of these lines perpendicular. 23 00:01:40,520 --> 00:01:43,700 And so now my Kangoo has been formed. 24 00:01:46,070 --> 00:01:50,780 Now I will add dimensions to it, so I want this edge to be. 25 00:01:52,160 --> 00:01:52,790 Twenty. 26 00:01:54,950 --> 00:01:57,510 And this one to be 30. 27 00:01:59,830 --> 00:02:01,300 I can now rotate this. 28 00:02:06,080 --> 00:02:08,340 So twenty four degrees. 29 00:02:08,419 --> 00:02:10,699 Twenty four point five degrees should be enough. 30 00:02:12,530 --> 00:02:15,200 And as you can see, our rectangle has been formed. 31 00:02:16,410 --> 00:02:16,980 And. 32 00:02:18,110 --> 00:02:21,860 Now, add dimensions, you can see it's 90 degrees. 33 00:02:22,520 --> 00:02:24,620 So I have found my perfect rectangle. 34 00:02:29,100 --> 00:02:35,730 In this second setting challenge, you will be required to insert and draw over a canvas infusion 360. 35 00:02:36,770 --> 00:02:42,530 This image right here is provided below this video, which is the canvas you will be inserted into Fusion 36 00:02:42,530 --> 00:02:43,130 360. 37 00:02:44,880 --> 00:02:49,110 Your second step will be to edit the canvas and place it at the center of your plane. 38 00:02:51,780 --> 00:02:59,340 The third step will be to calibrate the canvas and make sure that the height of the vase is 270 millimeters. 39 00:03:00,510 --> 00:03:06,210 Finally, you will use this line tool to sketch over the vase and then move it to complete the sketch. 40 00:03:07,170 --> 00:03:09,660 Positive ID, you know, and try this challenge. 41 00:03:12,850 --> 00:03:15,910 I will now insert the canvas into Fusion 360. 42 00:03:16,620 --> 00:03:19,780 Click on this button up here and insert from my computer. 43 00:03:22,320 --> 00:03:26,310 So I have my buzz image right here, and I will open it. 44 00:03:27,400 --> 00:03:28,930 And then I will select this thing. 45 00:03:30,710 --> 00:03:33,000 As you can see, our fuzzy image images appeared here. 46 00:03:33,320 --> 00:03:37,340 It is already at the center of my workspace, so I don't need to worry about it. 47 00:03:37,460 --> 00:03:38,570 And I can click, OK. 48 00:03:40,920 --> 00:03:42,750 I will now calibrate this. 49 00:03:44,280 --> 00:03:46,530 So it's like the top plane there. 50 00:03:47,880 --> 00:03:53,730 And this point here, I I want the distance to be 270 millimeters. 51 00:03:55,130 --> 00:03:59,660 So as you can see, our canvas has not been calibrated and it's ready to sketch over. 52 00:04:01,130 --> 00:04:04,730 Before I start sketching, I will tell you one thing. 53 00:04:05,120 --> 00:04:10,820 So as you can see, this image is in perspective and it's not an orthographic graphic image because 54 00:04:10,830 --> 00:04:12,770 as you can see, the bottom is good. 55 00:04:13,250 --> 00:04:17,329 So we will take the top curve and the bottom curve just as straight lines, and we won't talk about 56 00:04:17,329 --> 00:04:17,660 those. 57 00:04:18,740 --> 00:04:24,500 So I will use my firstly, I would use my line to create the base, so I will create the base. 58 00:04:24,590 --> 00:04:25,520 See there. 59 00:04:28,820 --> 00:04:32,960 And then I will use this line tool to go all around. 60 00:04:38,610 --> 00:04:39,030 There. 61 00:04:40,580 --> 00:04:40,840 Then. 62 00:04:43,170 --> 00:04:43,420 There. 63 00:04:48,900 --> 00:04:52,530 So our spine has been created, I would just adjust these points slightly. 64 00:04:57,230 --> 00:05:05,420 And our side chief of the bus has been full is to drive this point right there and then use the line 65 00:05:05,420 --> 00:05:07,890 to create the final lines. 66 00:05:15,120 --> 00:05:18,690 Now I will draw a line at the center because all the way up. 67 00:05:20,250 --> 00:05:22,860 And drag this point onto this line. 68 00:05:24,020 --> 00:05:25,700 So now we have a closed shape here. 69 00:05:28,380 --> 00:05:29,490 My bottom line is not. 70 00:05:31,440 --> 00:05:33,030 So I've been that straight as well. 71 00:05:33,510 --> 00:05:36,030 And I will just add a slight filmmaker. 72 00:05:39,120 --> 00:05:42,670 So now that this case has been created, we can it onto the other side. 73 00:05:42,720 --> 00:05:43,920 So expect a miracle. 74 00:05:44,670 --> 00:05:46,640 I will double click to select this entire thing. 75 00:05:46,680 --> 00:05:48,630 But now the Mirror Online has also been selected. 76 00:05:48,810 --> 00:05:53,760 So I would just click on it again to be selected, and then I will select my line, which is this. 77 00:05:55,080 --> 00:05:55,440 And it. 78 00:05:57,210 --> 00:06:00,540 So as you can see, our first sketch has now been formed. 79 00:06:06,540 --> 00:06:09,540 Your third sketching challenge will be a replication challenge. 80 00:06:10,140 --> 00:06:15,120 You will need to recreate this sketch of a watch crown right here. 81 00:06:16,590 --> 00:06:19,980 You will need certain tools which are mirror trim and patterns. 82 00:06:20,700 --> 00:06:27,000 The dimensions don't really matter, but try to get a similar shape to this positive ID, you know, 83 00:06:27,000 --> 00:06:27,780 and try this. 84 00:06:30,560 --> 00:06:36,830 To create the Watch Crown sketch, I will first create a soccer so type C on your keyboard and then 85 00:06:36,830 --> 00:06:40,700 struggle, let's say, 20 mm just for this demonstration. 86 00:06:42,400 --> 00:06:45,610 And then I will create a center line as a mirror line. 87 00:06:48,270 --> 00:06:53,340 Now I will create two more lines to create the. 88 00:06:54,680 --> 00:06:57,770 Intense in the watch crown. 89 00:07:03,350 --> 00:07:05,810 I was hit escape because I don't need like tools anymore. 90 00:07:06,350 --> 00:07:07,790 And then I will add a affiliate. 91 00:07:08,900 --> 00:07:09,500 Right here. 92 00:07:11,420 --> 00:07:14,870 Say zero point four mm should be no. 93 00:07:17,610 --> 00:07:20,460 And then I will trim this part. 94 00:07:22,880 --> 00:07:24,300 And this point. 95 00:07:34,100 --> 00:07:36,440 I will then mirror this. 96 00:07:39,460 --> 00:07:40,480 Onto the other side. 97 00:07:42,110 --> 00:07:46,700 Using this line that I have in the center and then click, OK. 98 00:07:49,910 --> 00:07:52,580 I will go ahead and also trim this. 99 00:07:53,850 --> 00:07:54,450 And this. 100 00:07:57,280 --> 00:07:58,870 I will add two more for this. 101 00:08:00,590 --> 00:08:01,250 On this. 102 00:08:02,830 --> 00:08:03,430 And this. 103 00:08:04,780 --> 00:08:06,730 Both measuring 0.2 millimeters. 104 00:08:08,680 --> 00:08:12,790 Now that that's done, we are ready to create a circular pattern, so I will double click on this. 105 00:08:13,030 --> 00:08:18,910 But as you can see our entire sketches inflected, I will dislike this line here and this means circle 106 00:08:18,920 --> 00:08:19,180 here. 107 00:08:19,840 --> 00:08:22,330 So now only that small part has been selected. 108 00:08:23,390 --> 00:08:26,180 They will then go to create create a circular pattern. 109 00:08:27,330 --> 00:08:29,280 And my objects have already been selected. 110 00:08:30,000 --> 00:08:37,440 And then I will select my point, which is this now my angular spacing will remain at full and let's 111 00:08:37,440 --> 00:08:45,930 say 15, Hudson's 15 might be too much, so this could add 10 or 12 to perfect. 112 00:08:47,040 --> 00:08:48,750 So now I will click OK. 113 00:08:52,500 --> 00:08:54,600 And now I can trim these. 114 00:08:57,340 --> 00:08:58,480 So that's the wrong one. 115 00:08:58,540 --> 00:09:01,510 So if you trim the wrong one by mistake, is it Kamanzi? 116 00:09:02,710 --> 00:09:05,320 And then get back to trimming this. 117 00:09:06,770 --> 00:09:07,280 This. 118 00:09:15,030 --> 00:09:16,170 And the last one. 119 00:09:18,070 --> 00:09:22,870 So now you can see my sketch has been created and it looks like a watch crown. 120 00:09:26,320 --> 00:09:28,810 Congratulations, if you go through all those challenges. 121 00:09:29,740 --> 00:09:33,430 And we are now done with the sketching module, once you are ready. 122 00:09:33,640 --> 00:09:38,560 Feel free to proceed to the next module where we begin creating 3D objects for you there.