1
00:00:00,210 --> 00:00:06,450
Welcome to the challenge video of Module four in this video, you will be faced with three challenges

2
00:00:06,930 --> 00:00:12,600
where you will be using your knowledge and skills from this module to create various 3D objects.

3
00:00:13,590 --> 00:00:18,900
For each challenge, I would first describe the challenge and tell you the tools required to complete

4
00:00:18,900 --> 00:00:19,080
it.

5
00:00:20,100 --> 00:00:23,370
You will then be able to pause the video and try it out for yourself.

6
00:00:24,920 --> 00:00:28,640
Finally, I will demonstrate how to go about each one of the challenges.

7
00:00:29,480 --> 00:00:31,610
Now let's get to the first challenge.

8
00:00:34,170 --> 00:00:39,720
In your first creation challenge, you will be required to use the loft and hold tools to create a 3D

9
00:00:39,720 --> 00:00:40,110
body.

10
00:00:41,380 --> 00:00:47,440
The first step will be to create an offset train 50 50mm above the XY plane or the bottom.

11
00:00:49,190 --> 00:00:55,610
Secondly, you will draw two rectangles, one on the plane and one on the offset plane you have created.

12
00:00:56,210 --> 00:00:59,120
The two measurements for the two rectangles are provided here.

13
00:01:01,300 --> 00:01:05,800
Next, you will be required to loft both these rectangles to create a 3D body.

14
00:01:06,790 --> 00:01:12,580
And finally, you will need to create a simple count sink hole on the top surface of the 3D body you've

15
00:01:12,580 --> 00:01:13,030
created.

16
00:01:14,330 --> 00:01:16,850
Pause the video now and try this challenge.

17
00:01:18,540 --> 00:01:21,780
Now that you've tried to challenge yourself, let me show you how to do it.

18
00:01:22,700 --> 00:01:24,710
So firstly, we need to create an offset plan.

19
00:01:25,360 --> 00:01:29,960
I would gone offset plane and then select the space plane or the plane here.

20
00:01:30,920 --> 00:01:36,290
I will drag my arrow up to 50mm and click, OK.

21
00:01:37,070 --> 00:01:38,840
So my offset plane has now been created.

22
00:01:39,920 --> 00:01:42,230
I will now create two new sketches.

23
00:01:42,920 --> 00:01:48,320
Firstly, on the X plane, this will be a rectangle.

24
00:01:49,620 --> 00:01:50,940
With the measurements of.

25
00:01:52,240 --> 00:01:54,790
Twenty five by 50.

26
00:01:56,880 --> 00:02:01,650
I will hit enter and finish the sketch, my base rectangle has been created.

27
00:02:02,700 --> 00:02:10,020
I will now create my second rectangle on this offset thing here, I will click on that and her command

28
00:02:10,020 --> 00:02:15,240
are using which I can make a center rectangle.

29
00:02:16,410 --> 00:02:22,650
And this will be 30 by 15mm.

30
00:02:24,780 --> 00:02:30,990
I can hit enter and finish sketch now that my two rectangles have been created.

31
00:02:31,230 --> 00:02:36,120
I can then loft, so go over to create and click on Loft.

32
00:02:37,860 --> 00:02:41,820
I reflect my bottom profile, followed by my top profile.

33
00:02:42,750 --> 00:02:45,900
And as you can see, a lot has been created.

34
00:02:46,860 --> 00:02:47,850
I will click OK.

35
00:02:49,430 --> 00:02:53,360
The final step is to create a whole so click on the whole to hear.

36
00:02:54,340 --> 00:02:55,780
And select the surface.

37
00:02:57,770 --> 00:03:02,690
So our whole has been created, I can map it to the center of the surface.

38
00:03:04,230 --> 00:03:06,210
I would change the whole time to count to think.

39
00:03:07,380 --> 00:03:10,170
The whole top remains simple.

40
00:03:11,340 --> 00:03:15,360
This I can change it to whatever measurement I like, let's say five.

41
00:03:16,920 --> 00:03:17,820
Mm.

42
00:03:21,270 --> 00:03:22,860
The diameter can be.

43
00:03:24,090 --> 00:03:24,720
Seven.

44
00:03:27,060 --> 00:03:29,490
And then the angle can be.

45
00:03:30,880 --> 00:03:31,450
Ninety.

46
00:03:33,580 --> 00:03:36,430
So as you can see, my desired hall has been created.

47
00:03:37,750 --> 00:03:40,090
And that is it for this challenge.

48
00:03:40,120 --> 00:03:41,440
Let's move on to the next one.

49
00:03:43,750 --> 00:03:49,360
For the second challenge of Module four, you will be required to recreate an object similar to the

50
00:03:49,360 --> 00:03:50,560
one shown on screen.

51
00:03:51,730 --> 00:03:57,340
You will create this object twice, once using the tool and once using the sweep tool.

52
00:03:58,710 --> 00:04:00,720
Note that the dimensions do not matter.

53
00:04:01,110 --> 00:04:06,840
However, the object that you create using the pipe, too has to be identical to the one you create

54
00:04:06,850 --> 00:04:07,680
using this week to.

55
00:04:08,630 --> 00:04:10,940
Plus, the video now and try this challenge.

56
00:04:12,030 --> 00:04:13,530
Now that you have given it a try.

57
00:04:13,770 --> 00:04:15,120
Let me show you how to do it.

58
00:04:16,019 --> 00:04:18,720
We will first use the pipe to create the object.

59
00:04:19,649 --> 00:04:21,269
First, we need to create a new sketch.

60
00:04:21,899 --> 00:04:23,460
I will choose the bottom plain here.

61
00:04:25,120 --> 00:04:26,980
And then create two lines.

62
00:04:30,420 --> 00:04:36,180
I will then use the filter to add the cost between these lines and hit enter.

63
00:04:38,060 --> 00:04:40,250
So now our sketch has been created.

64
00:04:41,640 --> 00:04:46,990
You can now use the pipe to in, create and then click on the path here.

65
00:04:48,620 --> 00:04:50,840
And you can see our pipe has been created.

66
00:04:51,820 --> 00:04:53,860
I will change section size to.

67
00:04:55,600 --> 00:04:56,890
Seven mm.

68
00:04:59,020 --> 00:05:05,290
And you can see that it looks fairly similar to the one we saw in the challenge preview.

69
00:05:06,250 --> 00:05:06,550
I will.

70
00:05:06,730 --> 00:05:07,150
OK.

71
00:05:08,140 --> 00:05:10,660
So this is one way of creating.

72
00:05:12,520 --> 00:05:19,420
This object using pipe, I will now delete this, sure, and head back to a sketch.

73
00:05:20,620 --> 00:05:24,070
I will now recreate the same object using the sweep tool.

74
00:05:25,020 --> 00:05:29,250
So in order to create created using these people, we first have to create another profile.

75
00:05:30,190 --> 00:05:31,600
Which is on this thing.

76
00:05:32,770 --> 00:05:39,910
Now, when we use the US, the pipe to our section sizes seven millimeters, hence we need to create

77
00:05:39,910 --> 00:05:43,060
a circle here that is seven millimeters as well.

78
00:05:44,260 --> 00:05:46,000
So will create that it OK?

79
00:05:47,250 --> 00:05:52,620
And finished my sketch, so now I have my two profiles ready to sweep.

80
00:05:53,430 --> 00:05:55,710
Head over to create and click on Sweep.

81
00:05:57,130 --> 00:06:00,730
I will select this profile first and then the boss.

82
00:06:03,240 --> 00:06:07,890
And the orientation would be perpendicular to the direction of the line.

83
00:06:09,560 --> 00:06:16,160
So there you can see, I have just recreated the same object using both the sweep and the pipe to.

84
00:06:17,130 --> 00:06:18,510
That is it for this challenge.

85
00:06:18,810 --> 00:06:20,100
Let's move on to the next one.

86
00:06:23,160 --> 00:06:25,470
This is the final challenge of Module four.

87
00:06:25,890 --> 00:06:30,240
It's a replication challenge, but it is also one of the most difficult challenges.

88
00:06:31,080 --> 00:06:33,600
You will first start off with a simple cylinder.

89
00:06:34,510 --> 00:06:39,970
And then use three tools coil mirror and Pattern to create this knowledge effect.

90
00:06:40,930 --> 00:06:42,400
Now this can be challenging.

91
00:06:43,030 --> 00:06:43,660
Try it.

92
00:06:44,050 --> 00:06:49,030
And if you still don't get it, then continue watching the video where I would show you how to do it

93
00:06:50,110 --> 00:06:51,100
because the video now.

94
00:06:51,280 --> 00:06:55,840
And try this challenge if you were able to complete that challenge successfully.

95
00:06:56,320 --> 00:06:58,810
It's really impressive, however.

96
00:06:59,140 --> 00:07:01,990
Don't worry if you did not, this was a hard challenge.

97
00:07:02,260 --> 00:07:03,730
I would show you how to do it now.

98
00:07:04,780 --> 00:07:11,350
So firstly, we need to create a cylinder head over to create and click on the cylinder two and select

99
00:07:11,350 --> 00:07:12,250
the best to ensure.

100
00:07:13,220 --> 00:07:17,990
I will then drag it out to create a circle of diameter 50.

101
00:07:19,590 --> 00:07:28,680
And then when I click, I can then drag this up to 50mm and hit, OK, so my cylinder has now been created.

102
00:07:30,700 --> 00:07:34,070
I will now use the call to to begin my knowledge.

103
00:07:35,260 --> 00:07:40,540
So go over to create coil, select the bottom of the cylinder.

104
00:07:42,280 --> 00:07:49,630
And then create a circle of 50mm because our cylinder has a diameter of 50.

105
00:07:51,470 --> 00:07:54,320
So Fusion has automatically created a quote for us.

106
00:07:55,410 --> 00:08:01,890
Drag it upward so that the bottom is touching the top, the bottom of the pile is touching the top,

107
00:08:01,890 --> 00:08:02,470
says Linda.

108
00:08:03,120 --> 00:08:04,590
So which would be fifty seven?

109
00:08:06,350 --> 00:08:07,170
Mm.

110
00:08:07,340 --> 00:08:08,120
So it's right there.

111
00:08:10,710 --> 00:08:15,120
And then we can change the number of revolutions to zero point two five.

112
00:08:16,930 --> 00:08:23,260
So we're not doing a full revolution, we're essentially doing a quarter of a revolution, which will

113
00:08:23,260 --> 00:08:24,640
give us that effect.

114
00:08:27,020 --> 00:08:33,020
Our section will be triangular in Canada and our section size, we can reduce it to one millimeter.

115
00:08:34,159 --> 00:08:40,789
So as soon as I changed to one millimeter, you can see it gives us this nice thin line.

116
00:08:41,720 --> 00:08:44,300
Now I can reduce the height.

117
00:08:45,550 --> 00:08:50,710
Bring it down, so 50mm seems fine and the operation would be cut.

118
00:08:51,860 --> 00:08:57,650
So now if I click on OK, you can see our small indent has been created there.

119
00:08:59,680 --> 00:09:05,320
Next, we need to mirror this on the other side so that we see that our lines go in both directions,

120
00:09:05,770 --> 00:09:07,210
creating the unnerving effect.

121
00:09:08,520 --> 00:09:14,760
So head over to create and click on Mirror, I will mirror Typekit features, and we will select this

122
00:09:14,760 --> 00:09:15,390
quiz here.

123
00:09:16,730 --> 00:09:19,400
And our plane will be the center plane here.

124
00:09:20,750 --> 00:09:24,980
And as you can see, it's been mirrored on the other side of the click, OK.

125
00:09:26,530 --> 00:09:33,640
So now that we have our two indents, it is time to create a pattern and create multiple iterations

126
00:09:33,640 --> 00:09:33,940
of that.

127
00:09:35,000 --> 00:09:44,320
So go to create pattern circular pattern again, your type of features and select the call and the myriad

128
00:09:45,200 --> 00:09:45,830
features.

129
00:09:46,920 --> 00:09:50,750
And your taxes will be this circular feature.

130
00:09:54,040 --> 00:10:02,440
So we are currently at 40 iterations, which looks about right to me and my angular spacing before,

131
00:10:03,190 --> 00:10:04,510
and I will click OK.

132
00:10:08,200 --> 00:10:14,830
Now, since we've done 40 iterations, it may take some time to compile it and create the final pattern.

133
00:10:15,640 --> 00:10:17,440
So we didn't wait for a while.

134
00:10:18,810 --> 00:10:25,680
So now our pattern has finally been created and we have been able to create the knuckling effect using.

135
00:10:26,880 --> 00:10:28,940
The call and patent to.

136
00:10:30,490 --> 00:10:32,560
And that is basically it for this video.

137
00:10:34,550 --> 00:10:37,280
Congratulations, if you go through all those challenges.

138
00:10:38,120 --> 00:10:42,230
And we are now done with this module once you are ready.

139
00:10:42,530 --> 00:10:46,910
Feel free to proceed to the next module where we begin modifying 3D objects.

140
00:10:47,570 --> 00:10:48,080
See you there!