1
00:00:00,330 --> 00:00:06,630
Welcome to the challenge video of Module six in this video, you will be faced with one assembly challenge,

2
00:00:06,870 --> 00:00:11,400
but you will be using your knowledge and skills from this module to create different types of joints.

3
00:00:12,360 --> 00:00:15,990
I will first describe the challenge and tell you the tools required to complete it.

4
00:00:16,830 --> 00:00:19,530
You will then be able to positive video and try it out yourself.

5
00:00:20,700 --> 00:00:22,650
I will then demonstrate how to go about it.

6
00:00:23,880 --> 00:00:25,980
Now let's get to our assembly challenge.

7
00:00:29,730 --> 00:00:34,560
In this challenge, you will first need to create two bodies, as shown on the screen.

8
00:00:35,590 --> 00:00:43,120
Note that the diameter of this hole and the diameter of this extension should be the same, the length

9
00:00:43,120 --> 00:00:46,270
of this hole and the length of this extension should also be the same.

10
00:00:47,480 --> 00:00:50,660
You need to do this in order to make sure that your joints work properly.

11
00:00:51,950 --> 00:00:57,140
Once you've created these two bodies, you need to create components from these bodies.

12
00:00:58,220 --> 00:01:00,050
Once the components have been created.

13
00:01:01,040 --> 00:01:05,000
You will create three separate joints using these same components.

14
00:01:06,370 --> 00:01:12,850
A rigid joint or joint and a slight, the joint was the video now and try this challenge.

15
00:01:14,410 --> 00:01:17,230
On my screen, you can see I have created the two bodies.

16
00:01:18,690 --> 00:01:21,930
I've also made sure that the whole regions are the same.

17
00:01:22,500 --> 00:01:28,860
So this has a radius of 15 and so does this, and both the whole and the extension have a length of

18
00:01:28,860 --> 00:01:29,100
put.

19
00:01:29,910 --> 00:01:31,860
So my joint can work properly.

20
00:01:33,080 --> 00:01:39,350
Now, I first need to create components from these bodies, so I will right click and click on create

21
00:01:39,360 --> 00:01:43,190
component from body and do the same for the other body.

22
00:01:45,090 --> 00:01:51,780
Now that I have my two components ready, I will rename the other members bottom and this one top.

23
00:01:54,380 --> 00:01:58,280
I'm not ready to create a joint, so I will click on the joint to.

24
00:01:59,990 --> 00:02:02,090
And now I need to select my two bodies.

25
00:02:04,370 --> 00:02:06,170
So firstly, I will select.

26
00:02:07,310 --> 00:02:10,940
The outermost point in this whole.

27
00:02:12,720 --> 00:02:17,430
And then I will select the lower most point on the other one.

28
00:02:22,720 --> 00:02:25,960
So this is our rigid joint.

29
00:02:27,730 --> 00:02:32,290
Now that are rigid joint has been created, we can move on to the next type of joint, which is irregular

30
00:02:32,290 --> 00:02:32,710
joint.

31
00:02:35,030 --> 00:02:42,050
We are currently on the Z-axis, which is what we want, and changing it to some other axis can make

32
00:02:42,050 --> 00:02:42,710
it go the other way.

33
00:02:42,830 --> 00:02:43,730
But we don't want that.

34
00:02:45,140 --> 00:02:48,440
So our revenue joint has also been created.

35
00:02:50,370 --> 00:02:55,350
And thirdly, we have our slide to join again, we want it on the x axis.

36
00:02:56,700 --> 00:02:57,540
So that is done.

37
00:02:58,490 --> 00:03:03,800
Now, we don't need to change anything for the privileged or rigid joints, but we do for the slider.

38
00:03:04,730 --> 00:03:11,360
So I will click OK and now I will go and edit my joint limits.

39
00:03:14,180 --> 00:03:18,680
So the motion is slide, and I need to set a minimum.

40
00:03:19,810 --> 00:03:24,100
And a maximum which is going to be 30.

41
00:03:26,720 --> 00:03:28,190
And now I will animated.

42
00:03:29,760 --> 00:03:36,990
So now you can see it only goes over range from zero to 30 mm and does not go beyond that.

43
00:03:38,540 --> 00:03:39,740
And I can click OK.

44
00:03:41,520 --> 00:03:47,190
So these are my three joints using the same components, and that is it for this video.

45
00:03:48,970 --> 00:03:51,310
Congratulations, if you got through that challenge.

46
00:03:52,090 --> 00:03:55,390
We are now done with this module once you are ready.

47
00:03:55,660 --> 00:03:59,590
Feel free to proceed to the next module where we begin rendering 3D objects.

48
00:04:00,340 --> 00:04:00,880
See of there.